|
Product Name |
Dye Green |
|
Part Number |
RXSOL-19-3347-025 |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Branch : Kandla, Mumbai , Chennai, Vizag, Kolkata, UAE , OMAN , CANADA and KENYA
|
Phone |
+91 22 20871200 - 1400 |
|
Fax |
+91 22 27612100 :::AOH :0091 9821214367 |
|
Email |
rxsolchemicals@gmail.com |
|
Website |
www.rxmraine.com |
|
Chemical Name |
Cas No |
EC No |
Whight |
Formula |
|
Brilliant Green |
633-03-4 |
211-190-1 |
100 % |
C27H34N2O4S |
|
Signal Word |
Danger |
|
Hazard Statements |
H317 May cause an allergic skin reaction. H318 Causes serious eye damage. |
|
Precautionary statements |
P261 Avoid breathing dust. P280 Wear protective gloves/ eye protection/ face protection. P302 + P352 IF ON SKIN: Wash with plenty of water. P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. |
|
Classification of the substance or mixture |
Not a hazardous substance or mixture according to Regulation (EC) No 1272/2008. |
|
Supplemental Hazard Statements |
None. |
|
Other hazards |
This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher. |
|
General advice |
Show this material safety data sheet to the doctor in attendance. |
|
If inhaled |
After inhalation: fresh air. |
|
Eye Contact |
After eye contact: rinse out with plenty of water. Immediately call in ophthalmologist. Remove contact lenses. |
|
Swallowed |
After swallowing: immediately make victim drink water (two glasses at most). Consult a physician. |
|
Skin Contact |
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Consult a physician. |
|
Inhalation |
Remove patient to fresh air, keep warm and at rest and get medical assistance in necessary. |
|
Ingestion |
Rinse mouth with water. Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a doctor or Poison Control Center immediately. |
|
Most important symptoms and effects, both acute and delaye |
The most important known symptoms and effects are described in the labelling (see section 2.2) and/or in section 11 |
|
Indication of any immediate medical attention and special treatment needed |
No data available |
|
Flammability |
May be combustible at high temperature. |
|
Suitable extinguishing media |
Water Foam Carbon dioxide (CO2) Dry powder |
|
Unsuitable extinguishing media |
For this substance/mixture no limitations of extinguishing agents are given. |
|
Special hazards arising from the substance or mixture |
Carbon oxides Nitrogen oxides (NOx) Sulfur oxides Combustible. Development of hazardous combustion gases or vapours possible in the event of fire. |
|
Further information |
Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system. |
Hazardous combustion
products |
Fire may cause the evolution of Sulphur oxides, nitrogen oxides. |
|
Advice for firefighters |
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing. |
|
Protective Equipment |
Use personal protective equipment. |
|
Specific Hazards Arising from the Chemical |
Has a fire-promoting effect due to the release of oxygen.
Ambient fire may liberate hazardous vapours. |
|
Personal precautions, protective equipment and emergency procedures |
Advice for non-emergency personnel: Avoid inhalation of dusts. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert. For personal protection see section 8. |
|
Spillage |
Oxidizing material. Stop leak if without risk. Avoid contact with a combustible material (wood, paper, oil, clothing...). Keep substance damp using water spray. Do not touch spilled material. Prevent entry into sewers, basements or confined areas dike if needed. Eliminate all ignition sources. Call for assistance on disposal. |
|
Personal Protection |
Advice for non-emergency personnel: Avoid inhalation of dusts. Evacuate the danger area, observe emergency procedures, consult an expert. Advice for emergency responders: Protective equipment see section 8. |
|
Enviromental Precaution |
Do not let product enter drains. |
Methods and materials for
containment and cleaning |
Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up dry. Dispose of properly. Clean up affected area. Avoid generation of dusts. |
|
Reference to other sections |
For disposal see section 13. |
|
Advice on protection against fire and explosion |
Keep away from open flames, hot surfaces and sources of ignition.Take precautionary measures against static discharge. |
|
Incompatible materials |
Keep away from alkalis, strong oxidizing agents and metals. Provide containment walls of adequate capacity to hold any accidental spills. |
|
Hygiene measures |
Change contaminated clothing. Preventive skin protection recommended. Wash hands after working with substance. For precautions see section 2.2. |
|
Precautions for safe handling |
For precautions see section 2.2. |
|
Conditions for safe storage, including any incompatibilities |
Store the container tightly closed in a dry, cool and well-ventilated place. Store apart from foodstuff containers or incompatible materials. |
|
Storage conditions |
Tightly closed. Dry. |
|
Storage class |
Storage class (TRGS 510): 11: Combustible Solids |
|
Specific end use(s) |
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated |
|
Exposure controls |
No specific additional engineering controls are required. Provide good natural or artificial ventilation. |
|
Engineering Control |
Use process enclosures, local exhaust ventilation, or other engineering controls to keep airborne levels below recommended exposure limits. If user operations generate dust, fume or mist, use ventilation to keep exposure to airborne contaminants below the exposure limit. |
|
Eye/face protection |
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Tightly fitting safety goggles |
|
Body Protection |
Protective clothing. |
|
Skin protection |
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de). Full contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:KCL 741 Dermatril® L This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de). Splash contact Material: Nitrile rubber Minimum layer thickness: 0,11 mm Break through time: 480 min Material tested:KCL 741 Dermatril® L |
|
Respiratory protection |
Required when dusts are generated. Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system. Recommended Filter type: Filter type P2 The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented. |
|
Other Protection Measure |
Handle in accordance with good industrial hygiene and safety practice. |
|
Control of environmental exposure |
Do not let product enter drains. |
|
Physical state |
Crystalline |
|
Colour |
Dark green |
|
Odour |
No data available |
|
Odor Threshold |
Not Applicable |
|
pH |
No data available |
|
Melting Point |
210 °C - dec. |
|
Boiling Point |
No data available |
|
Flash Point |
No data available |
|
Evaporation Rate |
Not Applicable |
|
Flammability (solid, gas) |
No data available |
|
Explosive limits |
No Data Available |
|
Lower flammability or explosive limits |
No data available |
|
Autoignition temperature |
No data available |
|
Decomposition temperature |
No data available |
|
Vapour pressure |
No data available |
|
Density |
No data available |
|
Relative Vapor Density |
No data available |
|
Freezing point |
No data available |
|
Specific Gravity |
No data available |
|
Partition coefficient |
log Pow: ca.0,76 at 20 °C |
|
Explosive properties |
No data available |
|
Solubility |
4,23 g/l at 20 °C |
|
Ignition temperature |
No information available. |
|
Particle characteristics |
No data available |
|
Reactivity |
The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed. |
|
Stability |
The product is chemically stable under standard ambient conditions (room temperature) . |
|
Possibility of hazardous reactions |
Violent reactions possible with: Strong oxidizing agents |
|
Conditions to avoid |
No data available |
|
Incompatible materials |
No data available |
|
Hazardous Polymerization |
In the event of fire: see section 5 |
|
Acute toxicity |
LD50 Oral - Rat - 313 mg/kg Acute toxicity estimate Oral - 313 mg/kg (ATE value derived from LD50/LC50 value) Inhalation: No data available Dermal: No data available |
|
Skin corrosion/irritation |
Remarks: Causes skin irritation. (ECHA) |
|
Serious eye damage/eye irritation |
Remarks: Causes serious eye damage. (ECHA) |
|
Respiratory or skin sensitization |
May cause an allergic skin reaction. (ECHA) |
|
Carcinogenicity |
No data available |
|
Germ cell mutagenicity |
Test Type: Ames test Test system: Escherichia coli/Salmonella typhimurium Method: OECD Test Guideline 471 Result: negative Test Type: Mutagenicity (mammal cell test): chromosome aberration. Method: OECD Test Guideline 473 Result: negative |
|
Reproductive toxicity |
No data available |
|
Specific target organ toxicity - single exposure |
No data available |
|
Endocrine disrupting properties |
The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher. RTECS: BP6825000 Nausea, Vomiting, Diarrhea To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated. |
|
Persistence and degradability |
No data available |
|
Toxicity to fish |
LC50 - Lepomis macrochirus - 0,0305 mg/l - 96 h Remarks: (Lit.) |
|
Toxicity to daphnia and other aquatic invertebrates |
Semi-static test EC50 - Daphnia magna (Water flea) - > 0,003 mg/l - 48 h (OECD Test Guideline 202) Remarks: (above the solubility limit in the test medium) |
|
Toxicity to bacteria |
EC50 - activated sludge - > 1.000 mg/l - 3 h (OECD Test Guideline 209) Remarks: (above the solubility limit in the test medium) |
|
Toxicity to algae |
Static test EC50 - Pseudokirchneriella subcapitata (green algae) - > 0,001 mg/l - 72 h (OECD Test Guideline 201) Remarks: (above the solubility limit in the test medium) |
|
Products Biodegradation |
The methods for determining the biological degradability are not applicable to inorganic substances. |
|
Mobility in soil |
No Information available |
|
Results of PBT and vPvB assessment |
This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher. |
|
Endocrine disrupting properties |
The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher. |
|
Other adverse effects |
No data available |
|
Disposal methods |
The material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems. |
|
Contaminated packaging |
Containers can be triply rinsed (or equivalent) and offered for recycling or reconditioning. Alternatively, the packaging can be punctured to make it unusable for other purposes and then be disposed of in a sanitary landfill. Controlled incineration with flue gas scrubbing is possible for combustible packaging materials. |
|
Waste treatment Method |
No data available |
|
UN number |
ADR/RID:3077 IMDG: 3077 IATA: 3077 |
|
UN proper shipping name |
ADR/RID:Environmentally hazardous substance, solid, n.o.s.
IMDG: Environmentally hazardous substance, solid, n.o.s.
IATA: Environmentally hazardous substance, solid, n.o.s.
|
|
Transport hazard class(es) |
ADR/RID: 9 IMDG: 9 IATA:9 |
|
Packaging group |
ADR/RID:III IMDG: III IATA: III |
|
Environmental hazards |
ADR/RID: No IMDG: No IATA: No |
|
Special precautions for user |
Tunnel restriction code : (C/E) |
|
Further information |
Not classified as dangerous in the meaning of transport regulations. |
|
Safety, health and environmental regulations/legislation specific for the substance or mixture |
This material safety data sheet complies with the requirements of Regulation (EC) No. 1907/2006. |
|
Other regulations |
Observe work restrictions regarding maternity protection in accordance to Dir 92/85/EEC or stricter national regulations where applicable. Take note of Dir 94/33/EC on the protection of young people at work. |
|
National legislation |
Seveso III: Directive 2012/18/EU of the European Parliament and of the Council on the control of major-accident hazards involving dangerous substances. E1 ENVIRONMENTAL HAZARDS |
|
Chemical Safety Assessment |
For this product a chemical safety assessment was not carried out |
|
Other Information |
The information above is believed to be accurate and represents the best information currently available to us. However, we make no warranty of merchantability or any other warranty, express or implied, with respect to such information, and weassume no liability resulting from its use. Users should make their own investigations to determine the suitability of the information for their particular purposes. In no event shall be liable for any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental, consequential or exemplary damages, howsoever arising, even if Rx Marine International has been advised of the possibility of such damages.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
|
