Zinc (II) Hydroxide
Zinc hydroxide, Zn(OH)2, is a white, water-insoluble, amphoteric hydroxide that dissolves in both acids and strong bases (forming zincates). It occurs naturally as the rare minerals wülfingite, ashoverite and sweetite. RXSOL supplies it to medical-dressing makers (as an absorbent coating on post-surgical bandages), to pesticide and pigment manufacturers as an intermediate, and to laboratories; it is also the precursor for other zinc salts and for zinc oxide on calcination.
- Part number
- RXSOL-19-1265-125
- Category
- Agriculture
- Brand
- RXSOL
Overview
Zinc hydroxide is a hydroxide of zinc, with the chemical formula Zn(OH)2. It is used in surgical dressings. Zinc is a metallic element with the atomic number 30. It is found in nature most often as the mineral sphalerite. It also occurs naturally as 3 rare minerals: wн_lfingite (orthorhombic), ashoverite and sweetite (both tetragonal).Though excess zinc in harmful, in smaller amounts it is an essential element for life, as it is a cofactor for over 300 enzymes and is found in just as many transcription factors.
Applications
Uses of Zinc Hydroxide – Zn(OH)2
- Used in medicine as an adsorbing agent.
- Utilised for careful dressings where it works as a retentive. Huge bandages that are utilised post-medical procedure are covered with the zinc compound for engrossing the blood from the injury.
- Used as an intermediate for commercial production of pesticides and pigments.
Dosage and directions
Zinc hydroxide is an inorganic chemical compound with formula Zn(OH)2. It occurs naturally in three rare minerals namely wulfingite, ashoverite and sweetite. It is an amphoteric hydroxide. Zinc hydroxide reacts with both bases and acids. It is an insoluble hydroxide which reacts with strong acid and gets dissolved.
Safety and SDS
Read the safety data sheet before handling. Wear suitable gloves and eye protection.
View safety data sheet
| Product Name | Zinc (II) Hydroxide |
| Part Number | RXSOL-19-1265-125 |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Branch : Kandla, Mumbai , Chennai, Vizag, Kolkata, UAE , OMAN , CANADA and KENYA
| Phone | +91 22 20871200 - 1400 |
| Fax | +91 22 27612100 :::AOH :0091 9821214367 |
| rxsolchemicals@gmail.com | |
| Website | www.rxmraine.com |
| Chemical Name | CAS | EC number | Weight | Formula |
| Zinc (II) Hydroxide | 20427-58-1 | 243-814-3 | > 98% | Zn(OH)2 |
| Signal Word | Warning. |
| Hazard Statements | H333 – May be harmful if inhaled. H316 – Causes mild skin irritation. H410 – Very toxic to aquatic life with long lasting effects. H320 – Causes eye irritation. |
| P280 Wear protective gloves.P305 + P351 + P338 | Wear eye protection/ face protection. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. |
| Precautionary statements(Prevention) | P273 – Avoid release to the environment. P264 – Wash all exposed external body areas thoroughly after handling. |
| Precautionary statements response | P391 – Collect spillage. P304+P312 – IF INHALED: Call a POISON CENTER / doctor/physician/first aider/if you feel unwell. P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P332+P313 – If skin irritation occurs: Get medical advice. P337+P313 – If eye irritation persists: Get medical advice / attention. |
| Classification of the substance or mixture | Not a hazardous substance or mixture according to Regulation (EC) No 1272/2008. |
| Supplemental Hazard Statements | None |
| Other hazards | This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher. |
| Label elements | No hazard pictogram, no signal word, no hazard statement(s), no precautionary statement(s) required |
| General advice | Consult a physician. Show this MSDS to the doctor. |
| If inhaled | If breathed in, move person into fresh air. If not breathing, give artificial respiration. |
| Eye Contact | Remove contact lenses and irrigate exposed eyes with copious amounts of water for at least 15 minutes. Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids. If irritation, pain, swelling, lacrimation, or photophobia persist after 15 minutes of irrigation, the patient should be seen in a healthcare facility.Eye injury should only be undertaken by skilled personnel. |
| Swallowed | Never give anything by mouth to an unconscious person. Rinse mouth with water. |
| Skin Contact | Immediately remove all contaminated clothing, including footwear. Flush skin and hair with running water (and soap if available). Seek medical attention in event of irritation. |
| Inhalation | Rinse mouth with water, Avoid to give anything by mouth to an unconscious person If fumes or combustion products are inhaled remove from contaminated area. Lay patient down. Keep warm and rested. Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiating first aid procedures. Apply artificial respiration if not breathing, preferably with a demand valve resuscitator, bagvalve mask device, or pocket mask as trained. Perform CPR if necessary. Transport to hospital, or doctor. |
| Ingestion | Immediately give a glass of water. First aid is not generally required. If in doubt, contact a doctor. |
| Symptoms and effects, both acute and delayed | Zinc hydroxide can irritate the respiratory tract. Prolonged skin contact can produce a severe dermatitis called oxide pox. Exposure to high levels of can cause metallic taste, marked thirst, coughing, fatigue, weakness, muscular pain, and nausea followed by fever and chills. Severe overexposure may result in bronchitis or pneumonia with a bluish tint to the skin. Reversible liver enzyme abnormalities. Diarrhoea. |
| Indication of any immediate medical attention and special treatment needed | Absorption of zinc compounds occurs in the small intestine. The metal is heavily protein bound. Elimination results primarily from faecal excretion. The usual measures for decontamination (Ipecac Syrup, lavage, charcoal or cathartics) may be administered, although patients usually have sufficient vomiting not to require them. CaNa2EDTA has been used successfully to normalise zinc levels and is the agent of choice. |
| Flammability | May be combustible at high temperature. |
| Suitable extinguishing media | Product is not flammable |
| Unsuitable extinguishing media | None known |
| Special hazards arising from the substance or mixture | Metal & metal oxide. |
| Further information | No data available |
|
Hazardous combustion products |
Fire may cause the evolution of Sulphur oxides, nitrogen oxides. |
| Advice for firefighters | Wear self-contained breathing apparatus for firefighting if necessary. |
| Fire fighting | Alert Fire Brigade and tell them location and nature of hazard. Wear breathing apparatus plus protective gloves in the event of a fire. Prevent, by any means available, spillage from entering drains or water courses. Use fire fighting procedures suitable for surrounding area. |
| Specific Hazards Arising from the Chemical |
Has a fire-promoting effect due to the release of oxygen. Ambient fire may liberate hazardous vapours. |
| Personal precautions, protective equipment and emergency procedures | Eyes: Wear safety goggles.Skin: Wear appropriate nitrile or rubber gloves, apron and safety shoes. Avoid contact with skin, eyes and clothing. Inhalation: Avoid dust formation. Avoid breathing dust, vapors. Wear respiratory protection. Other: Ensure adequate ventilation, Evacuate personnel to safe areas. Keep unprotected persons away. For details see Section 8 |
| Spillage | Oxidizing material. Stop leak if without risk. Avoid contact with a combustible material (wood, paper, oil, clothing...). Keep substance damp using water spray. Do not touch spilled material. Prevent entry into sewers, basements or confined areas dike if needed. Eliminate all ignition sources. Call for assistance on disposal. |
| Personal Protection | Advice for non-emergency personnel: Avoid inhalation of dusts. Evacuate the danger area, observe emergency procedures, consult an expert. Advice for emergency responders: Protective equipment see section 8. |
| Enviromental Precaution | Waste product should be handled and disposed of in a manner which complies with local, state / federal regulations. Zinc hydroxide may cause adverse long-term effects in the aquatic environment. Keep out of sewers, ditches or drains. For details see Section 12 |
|
Methods and materials for containment and cleaning |
Sweep & clean up material immediate for disposal or recovery. Remove all ignition sources. Avoid contact with skin and eyes. Control personal contact with the substance, by using protective equipment. |
| Advice on safe handling | Work under hood. Do not inhale substance/mixture. |
| Advice on protection against fire and explosion | Provide appropriate exhaust ventilation at places where dust is formed. |
| Incompatible materials | Keep away from alkalis, strong oxidizing agents and metals. Provide containment walls of adequate capacity to hold any accidental spills. |
| Hygiene measures | General industrial hygiene practice. For precautions see section 2.2. |
| Precautions for safe handling | Ensure good ventilation / exhaustion at work place. Keep bags / containers closed. Closed containers/bags should be opened in well – ventilated area. Avoid contact with skin, eyes and clothing. Wash hands with soap and water and other exposed areas with water after handling. Handle empty bags / containers with care. Prevent concentration in hollow and sumps. |
| Precautions for safe storage | Absorbs CO2 upon exposure to air. Keep bags / container closed when not in use. Store bags / containers under covered area, away from direct sunlight, sources of intense heat, or where freezing is possible. Store bags / containers away from incompatible chemicals (chlorinated rubber, zinc chloride, phosphoric acid etc). Inspect all incoming bags / containers before storage, to ensure bags / containers are properly labeled and not damaged. Have appropriate extinguishing equipment in the storage area. Empty bags / containers may contain residual particles; therefore, it should be handled with care. Never store food, feed, or drinking water in storage area. Do not store this material in open or unlabeled bags / containers |
| Conditions for safe storage, including any incompatibilities | Store the container tightly closed in a dry, cool and well-ventilated place. Store apart from foodstuff containers or incompatible materials. |
| Storage incompatibility | May react, explosively with magnesium and chlorinated rubber when heated Incompatible with linseed oil (may cause ignition) WARNING: Avoid or control reaction with peroxides. All transition metal peroxides should be considered as potentially explosive. For example transition metal complexes of alkyl hydroperoxides may decompose explosively. The pi-complexes formed between chromium(0), vanadium(0) and other transition metals (haloarene-metal complexes) and mono-or poly-fluorobenzene show extreme sensitivity to heat and are explosive. Metals and their oxides may react violently with chlorine trifluoride and bromine trifluoride. These trifluorides are hypergolic oxidisers. They ignite on contact (without external source of heat or ignition) with recognised fuels - contact with these materials, following an ambient or slightly elevated temperature, is often violent and may produce ignition. Avoid strong acids, bases. |
| Storage class | Storage class (TRGS 510): 13: Non Combustible Solids |
| Specific end use(s) | Apart from the uses mentioned in section 1.2 no other specific uses are stipulated |
| Handling | Keep away from heat. Keep away from sources of ignition. Keep away from combustible material.. Empty containers pose a fire risk, evaporate the residue under a fume hood. Ground all equipment containing material. Do not ingest. Do not breathe dust. Wear suitable protective clothing. In case of insufficient ventilation, wear suitable respiratory equipment. If ingested, seek medical advice immediately and show the container or the label. Avoid contact with skin and eyes. Keep away from incompatibles such as reducing agents, combustible materials, organic materials, metals |
| Advice on general occupational hygiene | Advice on safe handling Observe label precautions. Change contaminated clothing. Wash hands after working with substance. |
| Requirements for storage | Keep in cool and store under shade. |
| Occupational Exposure limit values | The product does not contain any relevant quantity of materials with critical values that have to be monitored at the work place. |
| Exposure controls | General protective hygienic measures: Keep away from foodstuffs, beverages and food, Instantly remove any solid and impregnated garments, Wash hands during breaks and at the end of the work, Maintain an ergonomically appropriate working environment, Handle in accordance with safety practice. Appropriate engineering controls Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed engineering controls can be highly effective in protecting workers and will typically be independent of worker interactions to provide this high level of protection. The basic types of engineering controls are: Process controls which involve changing the way a job activity or process is done to reduce the risk. Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilation that strategically "adds" and "removes" air in the work environment. |
| Engineering Control | Use process enclosures, local exhaust ventilation, or other engineering controls to keep airborne levels below recommended exposure limits. If user operations generate dust, fume or mist, use ventilation to keep exposure to airborne contaminants below the exposure limit. |
| Eye/face protection | Face shield. Safety glasses with side shields .Soft contact lenses may absorb and concentrate irritants. |
| Body Protection | Choose body protection in relation to its type, to the concentration and amount of dangerous substances, and to the specific work-place., The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace. |
| Skin protection | The selection of suitable gloves does not only depend on the material, but also on further marks of quality which vary from manufacturer to manufacturer. Where the chemical is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time for substances has to be obtained from the manufacturer of the protective gloves and has to be observed when making a final choice. Personal hygiene is a key element of effective hand care. Experience indicates that the following polymers are suitable as glove materials for protection against undissolved, dry solids, where abrasive particles are not present. o Polychloroprene. o Nitrile rubber. o Butyl rubber. Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (Without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands. Penetration time of glove material in minutes: > 480, Glove thickness: 0.11 mm. Complete suit protecting against chemicals, The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace. Wear safety shoes. |
| Respiratory protection | Respirators may be necessary when engineering and administrative controls do not adequately prevent exposures.The decision to use respiratory protection should be based on professional judgment that takes into account toxicity information, exposure measurement data, and frequency and likelihood of the worker's exposure - ensure users are not subject to high thermal loads which may result in heat stress or distress due to personal protective equipment (powered, positive flow, full face apparatus may be an option). Published occupational exposure limits, where they exist, will assist in determining the adequacy of the selected respiratory protection. These may be government mandated or vendor recommended. Certified respirators will be useful for protecting workers from inhalation of particulates when properly selected and fit tested as part of a complete respiratory protection program. Use approved positive flow mask if significant quantities of dust becomes airborne. Try to avoid creating dust conditions. |
| Other Protection Measure | Handle in accordance with good industrial hygiene and safety practice. |
| Control of environmental exposure | Do not let product enter drains. |
| Thermal hazards | No data available |
Gloves Suit
| Physical state | Solid. |
| Colour | No data available |
| Odour | No data available |
| Odor Threshold | Not Applicable |
| pH | No data available |
| Melting Point | >= 133 - <= 154 °C |
| Boiling Point | No data available |
| Flash Point | Not Applicable |
| Evaporation Rate | Not Applicable |
| Flammability (solid, gas) | No data available |
| Explosive limits | No Data Available |
| Upper/lower flammability or explosive limits | No data available |
| Autoignition temperature | No data available |
| Decomposition temperature | 22 °C. |
| Vapour pressure | 24.5mmHg at 25°C |
| Density | 3.11 g/cm³. |
| Vapour Density | No Data Available |
| Freezing point | No data available |
| Specific Gravity | No data available |
| Partition coefficient | No data available |
| Explosive properties | No data available |
| Solubility | Water: 648 mg/L. Temperature:20 °C. pH:> 6.81 - < 6.94. |
| Ignition temperature | No information available. |
| Particle characteristics | No data available |
| Reactivity | Not inherently chemically reactive. Zinc hydroxide and chlorinated rubber reacts violently. Contact with magnesium and linseed oil can cause violent reaction. Contact with strong acids may cause vigorous reaction. Contact with strong bases will form water and soluble zincates. Contact between zinc oxide and hydrogen fluoride, aluminum + hexachloroethane, zinc chloride or phosphoric acid, and water should be avoided. |
| Stability | Stable under recommended storage conditions. Unstable in the presence of incompatible materials. Hazardous polymerisation will not occur. |
| Possibility of hazardous reactions | Under normal conditions of storage and use, hazardous reactions will not occur. |
| Conditions to avoid | Avoid humidity, Keep away from acid & alkali. |
| Incompatible materials | Acids, oxidizing agents. |
| Hazardous Polymerization | Under normal conditions of storage and use, hazardous decomposition products should not be produced. |
| Acute toxicity | Oral: No data available Inhalation: No data available Dermal: No data available |
| Skin corrosion/irritation | Remarks: No data available |
| Serious eye damage/eye irritation | No data available |
| Respiratory or skin sensitization | No data available |
| Serious eye damage/eye irritation | No data available |
| Toxic Effects on Human | May cause damage to the following organs: upper respiratory tract. Other Toxic Effects on Humans: Hazardous in case of skin contact (irritant, sensitizer), of ingestion, of inhalation (lung irritant, lung sensitizer). |
| Germ cell mutagenicity | Not active in genetics assay. |
| Reproductive toxicity | Not considered as reproductive toxicity. |
| Specific target organ toxicity - single exposure | No data available |
| Special Remarks on other Toxi Effects on Humans | Acute Potential Health Effects: Skin: Causes skin irritation. May cause skin sensitization, an allergic reation, which becomes evident upon re-exposure to this material. Eyes: Causes eye irritation. Ingestion: Causes gastrointestinal (digestive) tract irritation with nausea, vomiting, and diarrhea. May be harmful if swallowed. Inhalation: Causes respiratory tract irritation. May cause chemical pneumonitis and pulmonary edema, inflammation, edema of bronchi and larynx. Chronic Potential Health Effects: Repeated or prolonged skin exposure may cause allergic reactions in sensitive individuals. Repeated or prolonged exposure by inhalation may affect respiration and metabolism. |
| Additional Information | RTECS: AF3675000 Gastrointestinal disturbance To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated. After uptake of large quantities: muscular symptoms agitation Convulsions Headache Tremors Nausea psychoses |
| Endocrine disrupting properties | The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher. RTECS: QR7300000 To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated. |
| Persistence and degradability | No data available |
| Toxicity | Toxicity to fish LC50 - Oncorhynchus mykiss (rainbow trout) – 1.1 – 2.5 mg/l – 96 h Toxicity to daphnia and other aquatic invertebrates - EC50 - Daphnia magna – 0.0098 mg/l - 48 h Acute EC50 0.17 mg/l Algae Selenastrum Capricornutum - 72 hours |
| Bioaccumulative potential | No data available |
| Toxicity to fish | LC50 - Oryzias latipes - 0,90 mg/l - 96 h (OECD Test Guideline 203) |
| Toxicity to daphnia and other aquatic invertebrates | Immobilization EC50 - Daphnia magna (Water flea) - 17 mg/l - 24 h (OECD Test Guideline 202) |
| Toxicity to algae | EC50 - Pseudokirchneriella subcapitata - 0,14 mg/l - 72 h (OECD Test Guideline 201) |
| Eco Toxicity | Not Available |
| COD and BOD 5 | Not Available |
| Products Biodegradation | The methods for determining the biological degradability are not applicable to inorganic substances. |
| Mobility in soil | No Information available |
| Results of PBT and vPvB assessment | PBT/vPvB assessment not available as chemical safety assessment not required/not conducted |
| Endocrine disrupting properties | The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher |
| Other adverse effects | Environmental effects Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. Very toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. Do NOT allow product to come in contact with surface waters or to intertidal areas below the mean high water mark. Do not contaminate water when cleaning equipment or disposing of equipment wash-waters. Wastes resulting from use of the product must be disposed of on site or at approved waste sites. Metal-containing inorganic substances generally have negligible vapour pressure and are not expected to partition to air. Once released to surface waters and moist soils their fate depends on solubility and dissociation in water. Environmental processes (such as oxidation and the presence of acids or bases) may transform insoluble metals to more soluble ionic forms. Microbiological processes may also transform insoluble metals to more soluble forms. For zinc and its compounds: |
| Disposal methods | The generation of waste should be avoided or minimized wherever possible. Avoid dispersal or spilled material and runoff and contact with soil, waterways, drains and sewers. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. This product is recyclable. Consideration of disposal via this route should be given. |
| Contaminated packaging | Do not reuse empty Bags / containers. Dispose of as unused product, Recommend crushing, puncturing, or other means to prevent unauthorized use as per comply with local regulations for disposal The information offered in this section is for the product as shipped. Use and/or alterations to the product may significantly change the characteristics of the product and alter the waste classification and proper disposal methods. |
| Waste treatment Method | The material does not have an EPA waste number and is not a listed waste. Keep out of sewers, ditches or drains. All wastes must be handled and disposed of in accordance with applicable regulations |
| UN number | ADR/RID: 3077 IMDG: 3077 IATA: 3077 |
| UN proper shipping name |
ADR/RID:ZINC HYDROXIDE IMDG:ZINC HYDROXIDE IATA: ZINC HYDROXIDE |
| Transport hazard class(es) | ADR/RID: 9 IMDG: 9 IATA: 9 |
| Packaging group | ADR/RID: III IMDG: III IATA: III |
| Environmental hazards | ADR/RID: No IMDG: Yes, Marine pollutant IATA: No |
| Special precautions for user | Tunnel restriction code : (C/E) |
| Further information | Not classified as dangerous in the meaning of transport regulations. |
| Transport in bulk according to IMOinstruments | No data available |
| Inventory status | Components are on the following inventories: Polymaleic acid: - US TSCA, Canadian DSL, EU EINECS, Australian AICS, Korean, Philippine PICCS and Chinese Xi irritant R 36/38 Irritant to eyes & skin R 41 Risk of serious damage to eyes S24/25 Avoid contact with skin and eyes S26/28 In case of contact eyes & skin, rinse with plenty water and seek medical advice Section 312/313: Not listed. Not listed under California proposition 65. |
| Safety, health and environmental regulations/legislation specific for the substance or mixture | This material safety data sheet complies with the requirements of Regulation (EC) No. 1907/2006 |
| Safety, health and environmental regulations specific for the product in question | European Inventory of Existing Commercial Chemical Substances (EINECS) -Listed.EC Inventory Listed. United States Toxic Substances Control Act (TSCA) Inventory- Listed. China Catalog of Hazardous chemicals 2015 Not- Listed. New Zealand Inventory of Chemicals (NZIoC)Listed. PICCS -Listed. Vietnam National Chemical Inventory -Listed. IECSC Listed. Korea Existing Chemicals List (KECL) -Listed. |
| Other regulations | Observe work restrictions regarding maternity protection in accordance to Dir 92/85/EEC or stricter national regulations where applicable. Take note of Dir 94/33/EC on the protection of young people at work. |
| Chemical Safety Assessment | For this product a chemical safety assessment was not carried out. |
| Other Information |
The information above is believed to be accurate and represents the best information currently available to us. However, we make no warranty of merchantability or any other warranty, express or implied, with respect to such information, and weassume no liability resulting from its use. Users should make their own investigations to determine the suitability of the information for their particular purposes. In no event shall be liable for any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental, consequential or exemplary damages, howsoever arising, even if Rx Marine International has been advised of the possibility of such damages. DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable. |
Availability
Zinc (II) Hydroxide manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai, Sharjah, UAE, Gulf, Middle East, Muscat Oman, Kenya Africa. Get the best quality of Zinc (II) Hydroxide at a competitive price from us. We have ready stock of Zinc (II) Hydroxide in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.
Frequently asked questions
Zn(OH)2 chemical name?
Zinc(II) hydroxide (zinc dihydroxide).
Is zinc hydroxide soluble in water?
No — practically insoluble; it dissolves in acids (giving zinc salts) and in excess alkali (giving zincate).
Pack sizes?
500 g and 1 kg lab packs; 25 kg industrial.
