Buffer Cleaner
Oman Chemical is leading one Largest Supplier, Manufacture a
Your shopping cart is empty.
Direct exposure of Chlorine gas, can damage skin and its gas form irritates the mucous membrane.
Standard regional pack sizes are listed below and custom packaging can be provided worldwide. This product should be protected from freezing.
| Specifications | |
| Appearance: | Yellow to liquid |
| pH (10% solution): | 2.9 |
|
Specific Gravity@20oC: |
1.67 - 1.2 |
Application:
Antiscalant RXSOL-33-3302-
Other valuable RO CHEMICALS :
MAGNESIUM SULPHATE (HEPTA HYDRATE 99.5% MIN)
ANTISCALANT INDION 8510
SODIUM META BAI SULPHATE (SMBS)
ANTISCALANT SWM 700
SODIUM HYPO CLORIDE (CLORIN)10-12 %
Inspect all cleaning system components to include CIP tank, hoses, and cartridge filters. Flush or replace if necessary. Fill cleaning tank with RO permeate or DI water. Turn on agitator or tank recirculation pump.
Slowly add ORG MC 882 to cleaning tank (1 gal [3.8 L] of ORG MC 882 for every 50 gal [189 L] of water). Mix thoroughly. The solution pH should match product specification. If necessary, adjust pH with a membrane–approved chemical such as caustic, citric, sulfuric or hydrochloric acid. The solution should be heated up to 45˚C to improve cleaning efficacy.
Circulate solution in the same direction as the feed flow. Typical circulation times are 30–90 minutes.* PWT recommends cleaning each stage of the system separately. Maximum flow rate per pressure vessel is 40 gpm (152 Lpm) for 8-inch elements and 10 gpm (38 Lpm) for 4-inch elements. Maximum pressure for cleaning is 60 psig (4.2 kg/cm2).
In cases of heavy fouling, divert the first 10-20% of cleaning solution to drain to prevent re–deposition of removed solids.Rinse with RO permeate before returning system to service. When returning unit to service, divert product water to drain until any residual cleaning solution has been rinsed from system. LIQUID MEMBRANE CLEANER
This Acidic Nature product is specialized to clean RO/NF/UF membranes in a safe and effective manner.
PHYSICAL & CHEMICAL PROPERTIES
These properties are typical. Refer to the Material Safety Data Sheet (MSDS) SECTION 9, for the most current data.
| Color: | Clear, Yellow |
| Form: | Liquid |
| Odor: | Slight ammonia smell |
| Density: | 11.33 lb/gal |
| Specific Gravity @ 25oC (77oF): | 1.36 |
| pH (Neat): | 10.5 |
| Freeze-Thaw Recovery: | Complete |
| Viscosity @ 25oC (77oF): | 20 cp |
| Flash Point (PMCC): | None |
| Solubility in Water: | Complete |
| Freeze Point: | 32oF (0oC) |
| Volatile Organic Compounds (VOC): | 0% |
RO antiscant
Scaling is caused in membranes because the level of hardness salts in the water becomes highly concentrated as it passes through the RO unit. In smaller units scale formation can be prevented by base exchange softening the make-up water but for larger systems that is very expensive. We have developed a range of easy to handle, cost effective RO Antiscalant which increase the solubility of the hardness salts so they remain in solution rather than forming scale on the membrane. Our cost effective RO antiscalants will inhibit a wide range of foulants including: calcium carbonate, calcium sulphate, barium sulphate, strontium sulphate, calcium fluoride, silica and iron.
RO Antiscalants are dosed directly to the RO feed water tank or feed water line (after pretreatment) at the recommended dosage of 1-3 mg/L and maximum dosage at 8mg/L, subject to inlet water quality and parameters is respect of Calcium Hardness, Iron, TDS, Alkalinity, pH and silica content. Maximum dilution should be 10% with RO or DI water for temperature less than 30 deg C. For higher temperature the dilution ratio can increase.
Key Features and Benefits
It reduces the risk of scaling and eliminates the use of hazardous acids,resulting in efficient plant operation with highest possible conversion rate.
It is a very effective antiscalant . It is also compatible with RO CHEMICALS series of coagulant and flocculants (polyelectrolytes). Our RO Antiscalant (HIGH PH) is effective in minimizing scaling in presence of foulants like Calcium Carbonate, Sulfate salts of Calcium, Barium, Strontium and Magnesium, Calcium Fluoride, Iron and Silica.
Key Features and Benefits
Application and Dosage
Our RO Antiscalant (HIGH PH) is dosed directly to the RO feed water tank or feed water line (after pretreatment) at the minimum recommended dosage of 1ppm and maximum dosage at 15ppm, subject to inlet water quality and parameters is respect of Calcium Hardness, Iron, TDS, Alkalinity, pH and silica content.
In case of high iron content of about 0.5 to 1.0ppm, the dosing has to be increased by 10-15ppm for stabilizing Calcium.
At about 10-15ppm dosage our RO Antiscalant (HIGH PH) is capable of fully inhibiting iron and calcium, and silica up to 166ppm. For higher silica content RXSOL ANTISCALANT should be used.
Antiscalant RO RXSOL-33-3302-025
Antiscalant C.I ALKA RXSOL-33-2034-025
Membrane Antiscalant ALKA 191T RXSOL-33-3321-030
Antiscalant ORG EV 2030 RXSOL-33-3325-230
Antiscalant RXSOL ORG EV RXSOL-33-3327
| Physical State | Powder, solid, Liquid, Granules, Crystals |
| Usage | RO MEMBRANE claning chemicals Industrial, Commerical |
| Packaging Type | JAR |
| Grade Standard | Technical Grade |
| Packaging Size | 10 kg / 20 Kg |
pH adjusted to 3.0+ 0.5
Highly effective at ambient temperatures
Contains no surfactants and is quickly rinsed away
ORG Clean MC 103 Membrane Cleaner is balanced acidic low pH powder / crystal product specialize to remove metal hydroxides, calcium carbonate and other similar scales from polyamide, polysulfone and thin film, composite membrane surfaces.
ORG Clean MC 103 Membrane Cleaner is advanced, high strength powder to clean Membrane from fouling.
We are marine chemical supplier since 1996.These Marine Chemicals include different sets of products such as Tank Cleaners, Maintenance Chemicals, Cooling Water Treatment Chemicals, Boiler Water Treatment Chemicals, Fuel Additives, etc.
Oman Chemical is leading one Largest Supplier, Manufacture a
Oman Chemical is leading one Largest Supplier, Manufacture a
